Page 1 of 1
ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Wed Jan 15, 2020 4:06 pm
by pilotxpl737
Hello,
my ATC-COM procedure suspended at status of starting the departure-communication.
"Read back correct. Call me again for departure".
There is no possibility to activate the departure call. There is no departure frequency shown in the displayed
124thATC-menu (radio departure shows 0.00) although(!) in the loading logfile found the dep frequency 11952.
How proceeding the ATC Radio dialog process ? Any helping ideas ?
(124thATC v60 /xpl 10 installed)
Thx and regards
pilotxpl737
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Sun Jan 19, 2020 11:15 am
by ntnll
pilotxpl737 wrote: ↑Wed Jan 15, 2020 4:06 pm
Hello,
my ATC-COM procedure suspended at status of starting the departure-communication.
"Read back correct. Call me again for departure".
There is no possibility to activate the departure call. There is no departure frequency shown in the displayed
124thATC-menu (radio departure shows 0.00) although(!) in the loading logfile found the dep frequency 11952.
How proceeding the ATC Radio dialog process ? Any helping ideas ?
(124thATC v60 /xpl 10 installed)
Thx and regards
pilotxpl737
Hi pilotxpl737,
"contact me" means contact back without change frequency. Departure is found 0.00 in the apt.dat, so in not gonna be used.
You should not change the frequency, and receive the hand-off and a get a dilaog again, when your distance from the runway will be below the "holding point radius" option value.
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Sun Jan 19, 2020 7:57 pm
by pilotxpl737
ntnll wrote: ↑Sun Jan 19, 2020 11:15 am
pilotxpl737 wrote: ↑Wed Jan 15, 2020 4:06 pm
Hello,
my ATC-COM procedure suspended at status of starting the departure-communication.
"Read back correct. Call me again for departure".
There is no possibility to activate the departure call. There is no departure frequency shown in the displayed
124thATC-menu (radio departure shows 0.00) although(!) in the loading logfile found the dep frequency 11952.
How proceeding the ATC Radio dialog process ? Any helping ideas ?
(124thATC v60 /xpl 10 installed)
Thx and regards
pilotxpl737
Hi pilotxpl737,
"contact me" means contact back without change frequency. Departure is found 0.00 in the apt.dat, so in not gonna be used.
You should not change the frequency, and receive the hand-off and a get a dilaog again, when your distance from the runway will be below the "holding point radius" option value.
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Sun Jan 19, 2020 8:02 pm
by pilotxpl737
Hi ntnll,
thanks, but as you see in the enclosed .pdf (marked blue) the value "holding point radius " is good. It is only 0.01.
regards pilotxpl737
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Sun Jan 19, 2020 8:55 pm
by ntnll
pilotxpl737 wrote: ↑Sun Jan 19, 2020 8:02 pm
Hi ntnll,
thanks, but as you see in the enclosed .pdf (marked blue) the value "holding point radius " is good. It is only 0.01.
regards pilotxpl737
Within the radius, try to switch over tower and ground, do you get any dialog?
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Mon Jan 20, 2020 11:37 am
by pilotxpl737
Hi ntnll,
switching between the tower and ground nothing happens.
Message "Read back correct. Call me again for departure" is still shown
as you can see in the screenshot in the first post. Also you can see in the log.file
it shows "departure frequency found 119.52"
regards pilotxpl737
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Wed Jan 22, 2020 3:34 pm
by ntnll
pilotxpl737 wrote: ↑Mon Jan 20, 2020 11:37 am
Hi ntnll,
switching between the tower and ground nothing happens.
Message "Read back correct. Call me again for departure" is still shown
as you can see in the screenshot in the first post. Also you can see in the log.file
it shows "departure frequency found 119.52"
regards pilotxpl737
Hi pilotxpl737,
Your the only user so far reporting this issue, I also not able to replicate it on my computer, I'll keep doing further tests.
Thanks for reporting,
a.
Re: ATC Radio COM- procedure stopped, dep frequency not transferred
Posted: Wed Jan 22, 2020 7:14 pm
by pilotxpl737
ntnll wrote: ↑Wed Jan 22, 2020 3:34 pm
pilotxpl737 wrote: ↑Mon Jan 20, 2020 11:37 am
Hi ntnll,
switching between the tower and ground nothing happens.
Message "Read back correct. Call me again for departure" is still shown
as you can see in the screenshot in the first post. Also you can see in the log.file
it shows "departure frequency found 119.52"
regards pilotxpl737
Hi pilotxpl737,
Your the only user so far reporting this issue, I also not able to replicate it on my computer, I'll keep doing further tests.
Thanks for reporting,
a.
Hi ntnll,
thanks for answering.
Try it with LSGG Geneva according to my bugreport.
But still a very good addon, good job !!
)
regards pilotxpl737